INSTEON ControLinc Tabletop Controller

If this is your first INSTEON installation, the best way to get everything needed to start your lighting automation is with one of these three starter kits:

• INSTEON Lamp Scene Lighting Starter Kit, which includes two INSTEON LampLinc Dimmer (3-Pin) plug-in modules, two INSTEON Access Points (& Wireless Phase Couplers), and one INSTEON ControLinc Tabletop Controller.
  
  
• INSTEON Wire-in Dimmer Scene Lighting Starter Kit, which includes two INSTEON SwitchLinc Dimmers, two INSTEON SignaLinc RF Signal Extenders, and one INSTEON ControLinc Tabletop Controller.
  
  
• INSTEON Keypad Dimmer Scene Lighting Starter Kit, which includes one INSTEON KeypadLinc Dimmer, two INSTEON SignaLinc RF Signal Extenders, and two INSTEON SwitchLinc Dimmers.

These starter kits include everything required to set up your INSTEON network. Learn more about INSTEON here.

Setup

The ControLinc uses a simple "Plug-N-Tap" process to link to other INSTEON devices. Put the ControLinc in setup mode by pressing any of the five ON buttons for 10 seconds, and then press the button on the module you would like to control. That's all it takes to link the ControLinc to any INSTEON module!

Scene Capable

Each of the five ON/OFF buttons on the ControLinc can be set up to control one INSTEON module or multiple modules in a scene.

Works with Legacy X10 Products

Each of the five ON/OFF buttons on the ControLinc can be assigned an X10 address. This enables the ControLinc to bridge your INSTEON network with your legacy X10 network. The ControLinc ON/OFF buttons can be assigned any X10 address and do not have to be assigned sequentially. This makes the ControLinc an excellent replacement for your existing X10 mini-controller.

Certifications and Warranty

All INSTEON ControLinc products are safety approved. The factory for SmartLabs Design Products is ISO9001 certified. In order to meet the ISO 9001 standards, the entire factory underwent rigorous inspections of procedures and policies before being certified. The certification received was based on its dedication to high-quality management systems and strict adherence of quality-control systems and guidelines. Because of this, Smarthome stands behind the entire INSTEON ControLinc line of products with a full 2-year warranty.

Specifications
General
Brand:	SmartLabs, Inc.
Manufacturer:	Smarthome
Manufacturer Product No.:	2430, INSTEON ControLinc Tabletop Controller
UPC:	891114000181
Color:	Black
Warranty:	2 years (upgradeable to 7 years)
Operation
ON/OFF Button Pairs:	5 Scenes
ALL ON/ALL OFF Buttons:	Control all INSTEON and X10 devices linked to Channels 1-5
BRIGHT/DIM Buttons:	Control INSTEON and X10 devices linked to last pressed Channel
Audio Alert:	Beeper, can be disabled
Status LED:	White, can be disabled
Operation Modes:	INSTEON only, X10 only, INSTEON and X10 Combo Mode
Combo Mode Message Order:	INSTEON, X10, INSTEON cleanup
Setup Memory:	Non-volatile EEPROM
INSTEON Features
INSTEON Addresses:	1 hard-coded out of 16,777,216 possible
INSTEON Links:	417 out of 16,777,216 possible
INSTEON Powerline Frequency:	131.65 KHz
INSTEON Minimum Transmit Level:	3.2 Vpp into 5 Ohms
INSTEON Minimum Receive Level:	10 mV
INSTEON Messages Repeated:	Yes
Mechanical
Mounting:	Included desk stand (flat or vertical)
Button Type:	14 Carbon puck onto etched PCB switches
Button Appearance:	Roundish and rubbery
Button Labels:	Printable using template
Operating Conditions:	Indoors, 32 to 122°F, up to 85% relative humidity
Dimensions:	5.0" H x 6.4" W x 3.0" D
Weight:	1 lb 5 oz
Electrical
Supply Voltage:	120 Volts AC +/- 10%, 60 Hertz, single phase
Surge Protection:	MOV rated for 150 Volts
Power Cord:	6 ft, 2-pin polarized plug
Certification:	Safety tested for use in USA and Canada (ETL #3017581)
X10 Features
X10 Addresses:	Up to 5 of 256 possible
X10 Status Response:	Supported
X10 Powerline Frequency:	120 KHz
X10 Minimum Transmit Level:	3.2 Vpp into 5 Ohms
X10 Minimum Receive Level:	10 mVpp nominal
X10 Messages Repeated:	No

• INSTEON ControLinc V2
  
• Quick-start guide